CBUnmanned H753-SOM

PX4 v1.18

WARNING

PX4 не розробляє цей (або будь-який інший) автопілот. Contact the manufacturer for hardware support or compliance issues.

The CBUnmanned H753-SOM is a System-on-Module (SoM) flight controller built around the STM32H753 microcontroller. It is intended to be mounted on a carrier board that breaks out the I/O and provides power, peripherals, and connectors for a specific vehicle integration.

INFO

This flight controller is manufacturer supported.

Основні характеристики

• MCU: STM32H753 (32-bit Arm® Cortex®-M7, 480 MHz, 2 MB Flash, 1 MB RAM)
• IMU: Dual InvenSense ICM-42670-P (on SPI4)
• Barometer: ST LPS22HB (on I2C1)
• Storage: microSD card (SDMMC2)
• Interfaces:
  • 6x user UARTs (TEL1, TEL2, TEL3, GPS1, GPS2, RC) plus a debug console — flow control on TEL1/TEL2/TEL3
  • 2x CAN (UAVCAN)
  • 2x external I2C (one per GPS port for compass) and 1x internal I2C (barometer)
  • 1x external SPI (the dual IMUs are on a separate internal SPI bus)
  • 9x PWM outputs (DShot / Bi-Directional DShot supported)
  • USB
  • Ethernet optional
• Power: Powered from an external regulated 5 V supply (e.g. a BEC on the carrier board). Battery voltage (up to 65 V) and current are monitored via ADC; the voltage sense input is a separate pin behind a voltage divider and does not power the board.

INFO

CAN transceivers require a 5 V supply. USB-only power (≈4.5 V after the input diode) is not sufficient to operate the CAN bus.

Де купити

Check CBUnmanned for availability.

Збірка прошивки

TIP

Most users will not need to build this firmware. It is pre-built and automatically installed by QGroundControl when appropriate hardware is connected.

To build PX4 for this target from source:

make cbunmanned_h753-som_default

Налаштування послідовного порту

UART	Пристрій	PX4 Default	Pins (TX / RX)	Flow Control (CTS / RTS)
USART2	/dev/ttyS0	TEL1	PD5 / PA3	PA0 / PD4
USART3	/dev/ttyS1	GPS1	PD8 / PD9	—
UART4	/dev/ttyS2	GPS2	PC10 / PC11	—
UART5	/dev/ttyS3	Консоль	PC12 / PD2	—
USART6	/dev/ttyS4	RC	PC6 / PC7	—
UART7	/dev/ttyS5	TEL2	PE8 / PE7	PE10 / PE9
UART8	/dev/ttyS6	TEL3	PE1 / PE0	PD14 / PD15

PWM Виходи

The board provides 9 PWM outputs, all of which support DShot and Bidirectional DShot.

The outputs are split across 4 timer groups:

Виводи	Таймер
1, 2, 3	Timer1
4, 5	Timer2
6, 7, 8	Timer3
9	Timer4

All outputs within the same group must use the same protocol and update rate.

Відладочний порт

The system console runs on UART5 (PC12 / PD2). USB CDC ACM is auto-started and provides MAVLink access.

Оновлення завантажувача PX4

Boards that ship without the PX4 bootloader must have it flashed before PX4 firmware can be installed. Download the cbunmanned_h753-som_bootloader.bin bootloader binary and follow the DFU Bootloader Update instructions.

Once the PX4 bootloader is flashed, firmware can be installed normally via QGroundControl.